Warm area, cool area and hides

If heating is specified, place it at one end and distribute hides between that area and the cool side. Choose openings and internal space suitable for the body; after adding bedding, check that entrances remain clear. Set the dish on a stable base and leave routes between retreats; use low supports only where suitable for the species.

Testing and access

Connect specified heat sources to compatible thermostats and guard against contact. Secure probes according to device instructions; measure air at resting sites and heated surfaces separately with independent instruments. In housing with water, also check water temperature and quality: one zone’s thermostat does not control the others.

With the complete enclosure running, record day and night readings and compare them with the sheet. Test doors, cable openings and cleaning access, keeping vents clear. Change one variable at a time and recheck after each adjustment.

Light in the animal’s daily life

Provide warm and cool opaque hides and voluntary access to the UV patch. Night activity does not mean no daytime exposure: also check branches the python can use.

An example layout in the enclosure

To make the layout concrete, take housing measuring 122 × 61 × 61 cm, using the first dimensional configuration in the sheet. This is a mounting example: retain the conditions and any alternatives attached to the stated minimum.

In a wooden enclosure with internal lighting, imagine the tube 56 cm above the floor and the back or head at 25 cm. The geometric distance is therefore 31 cm. The branch or platform lies below animal height, according to body size. Place lighting over one side, with a route to fully screened retreats.

In a glass enclosure with a mesh roof, retain the same animal height and imagine the tube 5 cm above the mesh: distance becomes 41 cm. Mesh attenuates UV variably; ordinary glass roofs block UVB. Increasing the percentage alone is insufficient: measure beneath the mesh and adjust height, output or layout as needed.

These distances describe the example, not a safe clearance for every lamp. Select the source and adjust mounting until approximately UVI 2–3 is measured at animal height in the exposed position. Also respect the minimum clearance specified for the model used. Recheck with furnishings, guards and mesh installed, including the highest reachable points and animal growth.

Choosing and checking lighting

First define the patch that should illuminate the whole body and the route to a screened retreat. For a broad patch, select a linear tube with reflector; consider a compact only if its useful patch covers the body and leaves an accessible gradient. Check model, output, reflector and mounting distance, then compare measured UVI with the species target. Label UVB percentage alone cannot determine distance and intensity.

The decisive check uses a UVI metre facing the source at animal height. Check the centre and edges of the exposed patch, the highest supports and retreats, which must allow withdrawal from UV. Repeat after moving equipment, changing lamps and plant growth. Without a metre, use the manufacturer’s instructions and measurements for the exact configuration, including safety clearances.

When UVB or UVA are absent

When UVB is absent, an appropriate whole-prey diet can provide vitamin D3; do not automatically add supplements to prey. Dietary provision does not recreate every effect of light, so retain plans for controlled UVB exposure.

UVA contributes to environmental perception and behaviour and cannot be replaced by vitamins or calcium. A reptile UVB source normally also emits UVA: check its declared spectrum. If the existing lighting lacks it, complete the installation with a suitable source; an ordinary white LED does not guarantee UVA and a UVA-only lamp does not provide UVB.

Sex, maturity and readiness

Choose an adult female with good muscle condition and stable feeding: fattening her to a target weight does not demonstrate maturity. Confirm sex before introductions; spurs and size alone are insufficient.

Start a record for each breeding animal with identity, origin, documented age and previous weights. Compare the weight trend with growth and body condition; delay introductions for animals still growing rapidly, losing weight or recently acquired. Use stated ages as guidance alongside these checks. If sex cannot be identified reliably, obtain assessment by qualified personnel before pairing.

Preparation and seasonal cycle

Prepare a season with a regular photoperiod and stable gradient, without cold brumation. Log meals, sheds and refusals: reduced feeding may accompany the cycle but must be distinguished from weight loss or illness.

Before encounters, prepare and test offspring enclosures and have first foods available. Check records for regular adult feeding and good body condition, then verify access from exposed areas to retreats. If the species protocol includes seasonal changes, adjust settings gradually and record the response. Record night-time air, surface and egg temperatures separately, noting where each is measured. Keep water available throughout preparation.

Courtship and mating

Introduce the male to the female for observed encounters, alternating with separate periods. Record aligned tails and visible copulation; do not pull coupled animals apart or leave several males with the female.

Before laying and the nest

An observed ovulation may be followed by shedding about two weeks later and laying roughly 30 days after that shed. Prepare a sheltered nest large enough for the coils and clutch beforehand; these dates support planning but do not themselves confirm fertile eggs.

Maintain a suitable laying site even without a male: females can produce unfertilised eggs. Persistent straining without laying, weakness or tissue protruding from the vent require prompt veterinary assessment. Do not wait for a predicted laying date if these signs appear. Do not squeeze the abdomen, pull eggs or give drugs to induce laying without veterinary direction.

Egg incubation

A documented artificial incubation regime is about 31–32 °C, with first pipping often at 58–62 days. Maintain humid air inside the container and keep eggs away from free water. Maternal incubation requires microclimate monitoring and prolongs the female’s fast; do not heat the entire enclosure to egg temperature.

Test the system before laying with an independent probe at egg height. Use clean, labelled containers, closed but allowing air exchange, with room for eggs and hatchlings. Keep eggs in their original orientation and do not detach eggs glued to their support. The substrate should retain moisture without free water on the shell; check condensation and water loss, adding water at the edge of the substrate rather than onto eggs. Record temperature and events daily without needless opening. The stated times are approximate: do not increase heat to meet a date.

First meals and juvenile care

Allow each hatchling to emerge independently and absorb its yolk. House individually with a shelter and readily accessible water; after the first shed offer an appropriately slender thawed rodent. Record refusals and recheck conditions, hydration and prey size. If a hatchling loses weight or fails to establish feeding, seek veterinary assessment; assisted feeding should be decided and demonstrated by the veterinarian.

During the first weeks, monitor each youngster: a feeding group does not guarantee that every individual eats. Record intake, droppings and weight at regular intervals to follow growth and adapt housing and food size. Provide separate accommodation if competition prevents an individual from feeding or size differences become marked. Document repeated independent meals before transfer to another keeper.

Female recovery

After reproduction provide water and the usual balanced diet, initially in manageable portions; monitor weight, activity and return of appetite. Keep supplements and lighting consistent with the feeding guide. Avoid further introductions until the previous condition has recovered; later clutches may occur without another mating. Persistent straining, weakness or protruding tissue require veterinary attention, without squeezing the abdomen.

Equipment and example diary

Place the nest where it can be checked without dismantling the enclosure. Label containers with female identity and laying date and prepare the specified medium; for attached eggs, instead provide guards in place without detaching them. If using an incubator, install a thermostat and independent probe and test it before laying. Run offspring enclosures too and prepare scales and first food, reserving capacity for later clutches.

A consistent diary using actual dates helps follow reproduction in Python regius. Start with adult identity, weight and condition, then record observed encounters, laying or birth and development conditions. After emergence record the first meal actually accepted and each youngster’s growth while continuing to follow female recovery. Over time these records help identify your lineage’s pattern without turning approximate durations into deadlines.